Ruts and potholes return after rain
Water and repeated wheel loads move loose aggregate into the low areas and weaken the material beneath them.
Tomball, TX and Nearby Areas
Residential and acreage property access
Gravel & Crushed Concrete Driveway Installation in Tomball, TX
A driveway should give your family dependable access, not leave muddy wheel paths, deep ruts or loose material spreading into the lawn. PLS Landscaping builds residential aggregate driveways for ranch homes, acreage properties, detached garages, workshops and homes outside denser city areas. The work can include clearing, excavation, grading, subgrade preparation, aggregate placement, drainage shaping and compaction so the finished route is built around the property and the vehicles that will use it.
Serving Houston Since 2011
Residential Driveway Construction
Onsite Evaluation
When access becomes the daily problem
The top layer is not always the reason a driveway fails
Adding another load of gravel may hide the problem for a short time. If soft soil, poor drainage, an uneven profile or weak edges remain below it, traffic can quickly recreate the same ruts and low spots. A dependable installation starts by correcting what will support the driving surface.
The approach stays muddy or soft
Organic soil, weak subgrade or trapped runoff can leave tires sinking and mud following the family back toward the home.
Gravel spreads beyond the driveway
Uncontained edges, abrupt turns and an incorrect material profile allow stone to migrate into grass and planting areas.
Water follows the wheel paths
A flat or sunken surface can collect rainfall instead of moving it toward a suitable side slope or drainage route.
Built as a layered access surface
A driveway needs support below the visible gravel
The exact layer arrangement depends on soil, drainage, driveway length, expected vehicle loads and the selected aggregate. The purpose is consistent: create a stable route that sheds water and holds its shape under normal residential use.
Selected gravel or crushed concrete
The compacted driving surface and finished profile.
Aggregate base where required
A prepared structural layer selected for the site and intended traffic.
Separation fabric where appropriate
Used when conditions support separating aggregate from underlying soil.
Prepared and compacted subgrade
Weak, wet or organic material is addressed before the finished layers are installed.
Site preparation in the field
The surface performs better when the site is prepared first
These PLS project photographs show the type of existing conditions, machine work, material placement and drainage coordination that may be involved before an aggregate surface is completed. The actual scope is determined onsite.
Construction sequence
Build the route from the ground up
The order protects the completed surface and gives each layer a defined job.
Confirm use and access
Review driveway length, width, vehicles, gates, utilities, street connection and equipment access.
Set profile and drainage
Define the finished height, transitions, crown or cross slope and responsible runoff direction.
Clear and shape subgrade
Remove specified vegetation, organic material and unsuitable soil, then shape the driveway footprint.
Install applicable layers
Compact the subgrade and place fabric, aggregate base and surface material where included in the scope.
Shape the driving surface
Distribute the selected material, refine edges and transitions, and compact applicable layers.
Check the completed route
Review surface shape, transitions, access and the intended direction of runoff before demobilization.
Driveway access note: A connection to a public street, sidewalk, culvert or right of way may require approval and must follow applicable access requirements.
A better arrival home
Less mud at the door. More dependable access for everyday life.
A properly prepared aggregate driveway makes rainy days less frustrating. Vehicles have a defined route, children have a clearer place to walk around parked cars, and the family can reach the home, garage or workshop without crossing a soft, deeply rutted surface.
Other Tomball services
Continue planning the rest of the property
Driveway questions
Before installation begins
Do you install the complete gravel or crushed-concrete driveway?
Yes, when the complete construction is included in the estimate. The scope can cover clearing, excavation, grading, subgrade preparation, applicable fabric and base, selected surface aggregate, drainage shaping and compaction.
Is crushed concrete the same as decorative gravel?
No. These materials differ in particle shape, appearance, compaction behavior and intended use. Selection depends on the driveway profile, desired finish, site conditions and availability.
Can new gravel be placed over my existing driveway?
Sometimes, but the existing profile and base must first be evaluated. Deep ruts, soft areas, vegetation, poor drainage or contaminated material may require removal and correction before new aggregate is placed.
How do you keep water from running down the wheel paths?
The driveway may be shaped with a crown, cross slope or coordinated drainage route depending on the surrounding elevations. The correct method is selected after the outlet and property conditions are reviewed.
What affects the price of an aggregate driveway?
Pricing depends on dimensions, access, clearing, excavation, hauling, soil condition, material type, base requirements, drainage work, equipment, compaction and transitions to the road or structures.
Where do you provide this service?
PLS Landscaping evaluates residential projects in Tomball and nearby communities. Availability depends on project size, delivery access, equipment requirements and location.
Schedule an onsite evaluation
Plan a cleaner, more dependable way into your property
We will review the route, access, soil, elevations, water movement, intended vehicles and material options before defining the driveway scope.
Call for an Evaluation
Prefer Texting? Send Us a Message
Request Free Estimate
Opens our short contact form.
★★★★★READ GOOGLE REVIEWS
